Plusmark Get Plusmark
Work and events

How to count people at an event and stay under capacity

The number inside is everyone who came in minus everyone who left. Here's how to keep that number right at one door or several, and get a warning before you reach your venue's limit.

A large crowd at an indoor event
Photo: Filip Rankovic Grobgaard on Unsplash

To know how many people are inside, count everyone who comes in and take off everyone who goes out. The number left is who's in the room right now. Compare it with your venue's capacity, which comes from the local building or fire code, not from you, and you'll know when to start holding people at the door.

That sounds simple, and it is, as long as every door is covered and nobody loses count halfway through the evening. This guide covers the two ways to count, what to do with more than one entrance, and how to get a warning before you reach the limit.

The short version

  • Find your capacity first. It's set for your venue under the local building or fire code. Ask the venue or your local fire authority if you don't know it.
  • One door, one counter: add one for each person in, take one off for each person out.
  • Need the total attendance too? Use two counters, In and Out. Inside is In minus Out.
  • Several doors: one counter per door, and add them up at set times.

Start with your number

The most people a space can safely hold at one time is called its occupant load, or capacity. Canada's workplace safety centre, CCOHS, notes that the local building or fire code often regulates these numbers. In practice, the figure for a hall, a church, a bar or a classroom is worked out for that space by whoever enforces the code where you are, and it can differ from room to room in the same building.

So don't guess, and don't borrow a number from a similar venue. Check the sign or the permit for the room you're using, or ask the venue manager. For an outdoor event or a temporary setup, your local council or fire authority can tell you what applies. Once you have the number, write it down where every door counter can see it.

One counter: in and out

If there's one door that people use both ways, one counter does the job. Tap once for every person who walks in. When someone leaves, take one off. The number on the screen is always the number of people inside.

  • Count people, not groups. A family of four is four taps. It's easy to tap once for "a group" when the door gets busy, and that's where counts drift.
  • Pick a line. Count people as they cross the doorway, not as they join the queue, so nobody is counted before they're actually in.
  • Re-entry counts both ways. Someone stepping out for air is one off when they leave and one on when they come back.

The catch with one counter is that at the end of the night it tells you who's still inside, not how many came. If you need the attendance for a report, a sponsor or next year's planning, use two counters instead.

Two counters: In and Out

Make one counter called In and another called Out. Tap In for every arrival and Out for every departure. Two numbers give you two answers:

  • Inside right now is In minus Out.
  • Total attendance is simply the In number.

You do a little arithmetic, but you get a cleaner record, and if the numbers ever look wrong you can see which side slipped. Two counters also suit venues where the entrance and the exit are different doors: one person counts in at the front, another counts out at the back.

An audience seated in a hall, facing a screen
Photo: Jakob Dalbjörn on Unsplash

More than one door

With several entrances, give each door its own counter (or its own In and Out pair) and its own person. Then pick a rhythm for adding them up, such as every 15 or 30 minutes, or whenever the room starts to feel full. A quick message to whoever is in charge with each door's number is enough.

The UK's Health and Safety Executive lists hand counters at entry and exit points as one way to estimate how many people are in a venue, and suggests monitoring the overall number so the safe capacity isn't exceeded. That's the whole job: every way in and out is counted, and someone keeps the total.

Don't forget doors that aren't meant to be used. If people slip out through a side door or a fire exit, those departures never get taken off, and your count creeps up all evening even though the room is emptying.

Get a warning before the limit

Reaching capacity shouldn't be a surprise. Decide in advance what happens as you get close, for example "one in, one out" at the door, and set a warning that gives you time to act.

In Plusmark that's a limit: set the counter's goal to At most and enter your number. The counter shows how many places are left, and you get a warning buzz when you reach it. It never blocks a tap, because people still arrive whether the app likes it or not, and you need the count to stay true. You might set the limit a little below the official capacity, so the warning comes while there's still time to slow the queue.

Common mistakes

  • Starting at zero when people are already inside. Staff, volunteers, performers and vendors take up space too. Count them in before the doors open, or type the starting number with Set Count.
  • A door with no counter. Every way in and out needs someone on it, or needs to be closed.
  • Losing the count when the screen sleeps. Turn on Keep Screen On, or count from the Lock Screen so it doesn't matter.
  • Mixing up nights. If the event runs over several days, use a counter that starts fresh each day so Saturday doesn't carry on from Friday.
  • Counting the queue. Count people as they come through the door, not while they're waiting outside.

Count it with Plusmark

Plusmark works like a clicker for the door, on iPhone, iPad and Apple Watch:

  • The Visitors starter starts at zero each day and keeps every day before in History.
  • Subtract 1 sits above the pad for each person leaving. Or make two counters, In and Out.
  • Count from the Lock Screen. Start the counter's Live Activity and tap its + key with your iPhone locked, no Face ID needed. More in keep a counter on your Lock Screen.
  • A pad that keeps up. It counts the moment your thumb lands, one count per finger, so quick taps don't merge.
  • An iPad at the entrance gives you a big pad with History beside it.
  • Busy hours. History's Today view has a bar for every hour, so you can see when the rush came.

One thing to know: Plusmark keeps counters in your own iCloud. Taps from your own devices on the same Apple Account add up, but a counter can't be shared with someone else's account. If volunteers count on their own phones, each keeps their own number and you add them up. Share Count sends a count as text, like "Visitors: 146 of 200 today", which makes the check-ins quick.

The people counter guide walks through the setup, and the FAQ covers limits, sync and the Live Activity.

Count it with Plusmark

Plusmark is the tally counter for iPhone, iPad, iPhone Duo and Apple Watch. Name a counter, tap the big + pad, and every tap is saved with its time, with goals, widgets and Siri.